휠 스페이서 설치 방법
Wheel spacers are metal spacers that fit between a vehicle's hub and the wheel. Spacers come in a variety of thicknesses and relocate the wheel farther away from the hub. These are used to widen the track of the vehicle, leading to more stability and better handling, which is why they are often used on racecars. Wheel spacers can also make a car look better by locating the wheel in a more visually aggressive position. There are two types of spacers: One type simply slide onto the hub, while the other type bolt to the vehicle's wheel studs. Bolt-on spacers have another set of studs that the wheel installs onto.
1 단계
평평한 표면에 차나 트럭을 주차하십시오. 휠을 허브에 고정하는 러그 너트를 풉니다. 적절한 지점에서 차 아래의 플로어 잭을 밀고 차를 들어올립니다. 잭 스탠드에 차를 내립니다. 잭 스탠드에서 네 모서리가 모두 지지될 때까지 이 과정을 반복합니다.
2 단계
러그 너트 제거를 완료하십시오. 바퀴를 허브에서 밀어내고 방해가 되지 않게 놓으십시오. 러그 스터드에 탈지제를 뿌리고 헝겊으로 닦아냅니다. 매우 더러우면 와이어 브러시를 사용하여 실을 청소하십시오. 휠이 설치되는 허브 표면도 닦아냅니다.
3단계
볼트 온 유형이 아닌 경우 휠 스페이서를 스터드에 밀어 넣습니다.{0} 스페이서의 구멍을 휠 스터드와 정렬한 다음 허브에 단단히 고정될 때까지 스터드 위로 스페이서를 밉니다. 일부 차량(예: BMW)은 허브에 끼워지는 러그 볼트를 사용합니다. 이 경우 스페이서를 허브의 구멍과 정렬하십시오.
4단계
휠 스페이서의 볼트인 경우 휠 스페이서를 스터드에 놓습니다.{0} 스페이서가 허브에 볼트로 고정되도록 러그 너트를 스터드에 설치합니다. 볼트는 스페이서와 함께 제공되지만 스페이서가 없는 경우 자동차 부품점에서도 구입할 수 있습니다. 스페이서를 제자리에 고정하는 너트를 지침에 설명된 사양으로 조입니다. 약 90피트{2}}파운드가 될 것입니다.
5단계
휠을 러그 스터드에 밀어 넣어 스페이서에 단단히 고정되도록 합니다. 러그 렌치로 러그 너트(또는 러그 볼트)를 설치하고 조입니다. 차량의 다른 모서리에 대해서도 반복합니다.
6단계
플로어 잭을 차량 아래로 밀고 잭 스탠드를 제거할 수 있도록 차량을 들어 올립니다. 차량을 한 번에 한 모서리씩 지면으로 내립니다.
Tighten the lug nuts with a torque wrench in a crisscross, star pattern. Tighten them to the manufacturer's recommended setting, which should be anywhere from 70 to 90 foot-pounds, depending on the vehicle. Check the tightness of the lug nuts after the vehicle has been driven 100 miles.





